Відео

A small summary for whoever wonders like me: the depth is 24", the diameter is a little over 12", both can be very dependent on the local code.

Those simpson anchors might fail inspection, you need a tension tie on the top of two galv or ss 1/2" thru bolts from rim/band through guard post to adjacent blocking + joist. Especially over 30" deck height.

Me, who wished all pressure treated wood looked as perfect as this, instead of the garbage available

Too many and too long of commercials. Why have a commercial inside a commercial . Oh yea, greedy VP said this commercial needs to make a profit. I will learn to frame my deck somewhere else.

Why did you bury the post and not post to peer brackets? Won’t the post rot or decay faster?

Thanks for the information

F#@K your Municipality lol

Excellent training. My plan calls for triple 2x10s on a 6x6 like you did. Is this legal/good practice since there will only be 1.5" left to bolt onto? Thank you.

Devon and linzy have done an excellent video,very informative and Devon explains the job very well and is easy to understand. I have noticed that they did not have an overhang on the first step coming down off the deck. I understand that this is a code violation because the very first run down will be 3/4” short because the run is measured horizontally down from the step above.

I understand "code" mandates gap between deck and pool edge, BUT what about space needed to get winter cover over top and down side of pool ? Pools in north are actually covered more then half the year.

Excellent presentation for installation of deck rail posts including how to handle out of plumb posts and using temporary boards to hold post and blocking. Sigh. This gets a fair bit harder to do when the deck is already down and you are replacing half cut outside fascia mounted posts with full inside posts.

a couple more stringers and wouldn’t even need a tread or a face

My porch has two Posts 10 ft apart and one 4 ft apart. Each end of the railing, top and bottom, would attach to the post. Its a small Porch but my husband is disabled and needs the railing to keep him from falling off the porch. If i had a 10 ft section I could do these myself. 😢

Don’t tighten the hidden fasteners until The next board is put in place . Makes it easier to fit them together .

Miter cut the corners to hide the ugly edge!!

still need to hide the cut deck board to the picture frame board. leaving a gap you can see the raw edge

How tall should the post be from the deck floor up?

This is a great tutorial. Thanks . I’ve been looking for this

Is it best to use ground contact pressure treated lumber for the framework?or just pressure treated?

I have many doubts and you explained so well!!!! I understand everything!!!! I will do my own deck stair for my home. Thanks master!!!! Blessings!!!

Talks more than works. We all already know the operating modes

My deck is going to be a walk way between front deck and back.4 foot by 24 foot....same concept?

Very meticulous and easy to understand, Thanks

Way to much time , I would have had the pist already set and would not ever anchor to the house.Wrong wrong, wrong

Excellent detail. Thank you.

You have exposed cuts on your stairs. Maybe you could bevel the riser cuts on the fascia and bevel the riser board ends for a clean finish. You're to good to have this kind of fail. No exposed cuts allowed my friend.

Great video. One question, the beams of the middle deck are attached to the posts of the upper deck using hangers. How would you attach the beams of the middle deck to the upper deck if the beams were run perpendicular instead of horizontal?

One of many hokey ways to attach different manufacturers rail systems. This system is expensive and rattles when you walk

You don’t mention the fact that the brackets are fixed angle. You’re making it sound like there’s a choice.

Great thorough video But, I'm confused about how to install the breaker board joist.s Are they two double 2 x 8 joist hangers? how do you have clearance to screw/ nail joist hangers to the ledger board??thanks for clarifying this

So about the handrails?

Where's the video on how to build the deck frame?

Is it possible to install a cocktail rail on top of the Enhance Railing? If so, what additional parts are needed?

Very helpful, however, at 7:33 when you're showing a small gap to catch the boards as they reach the breaker board... how do you properly attach joists to the ledger so close together? Is there a special bracket?

She could build a deck for me anytime!

Hearing protection to hammer a rod into soft ground! Really!

what type of fasteners do you use to fasten the flashing to the house?

for the bottom flashing, shouldn't you leave a pencil width gap below the ledger board? so that there isn't water resting in contact with the bottom of it

why can the joists not conflict the rail post locations?

Complete lie!!

Every online deck building program only has one 2x10 beam with a deck at a 14 foot depth and 2x8's as joists. So why the 2 beams and attached at the ledger?

Why the two beams with a ledger on a span less than 14'?

nice bakery

How do you determine how many "ROWS" of beams are required? My understanding of this project and size of deck I thought only one beam would be required but the deck is being built with 2 beams.

suppose.... you wanted to make this deck example handicap accessible? Where would you plan putting access ramps into this design? I realize this was prob. not part of the scope of this deck, so if you were designing with this in mind- what could you think of that might be important?

What is the part number for the pre assembled stair panels?

What is the part number for the pre assembled stair panels?

Will the facia not warp being wider than the rim joist?